Building OpenEmbedded (Beta)
OpenEmbedded is a build environment that contains a large number of packages. It's possible to use OpenEmbedded to build a bootable image for certain chumby devices, such as the Falconwing-series of devices. These instructions assume you're using Ubuntu 10.04 LTE, though they can be adapted to work on different platforms.
Re-imaging a device requires access to the internal micro-SD port. You will also need a USB micro-SD reader of some sort. These can be obtained very cheaply, and sometimes can be found bundled with micro-SD media.
These instructions assume you're running on a Falconwing platform, such as the Hacker Board or a chumby One. If you're using a Silvermoon-based platform such as Infocast 8 or chumby 8, replace all instances of "falconwing" with "silvermoon".
Building OE can take several hours, since it pulls down the source for the entire world and builds every piece from scratch; the initial build configuration is also a bit finicky at times.
In order to facilitate rapid evaluation and development, you can launch one of our public, pre-built Amazon EC2 cloud instance images. Please see quickstarting OE for directions on how to do this.
Setting up the Environment
This assumes you're using Ubuntu 10.04 LTE
- Install prerequisites
- sudo aptitude install sed wget cvs subversion git-core coreutils unzip texi2html texinfo docbook-utils gawk python-pysqlite2 diffstat help2man make gcc build-essential g++ desktop-file-utils chrpath libxml2-utils xmlto screen python-ply libxml2-utils xsltproc python-progressbar python-psyco
- Make /bin/sh not be part of dash
- sudo dpkg-reconfigure dash # Select "No" at the prompt
- Fix mmap_min_addr
- sudo sh -c 'echo 0 > /proc/sys/vm/mmap_min_addr'
- sudo sh -c 'echo "vm.mmap_min_addr = 0" >> /etc/sysctl.conf'
- Download OpenEmbedded
- mkdir chumby-oe
- cd chumby-oe
- tar xvzf meta-chumby-1.2.tar.gz
- tar xvzf bitbake-1.12.0.tar.gz
- git clone git://git.openembedded.org/openembedded # This can take an hour or so
- If desired, customize the build process.
Building with OpenEmbedded
Every time you log onto your build system, you must set up the environment. There is a command called "setup-chumby.sh" that will do this for you. You must source the command and not run it. If you've installed openembedded to a path other than ~/chumby-oe/ you must edit the command and change the variable TOPDIR.
Once setup, you use the bitbake command to build packages and images. Valid image files can be found in openembedded/recipes/images/and meta-chumby/recipes/images, and a full build from scratch can take ten hours or more. Building individual recipes is much quicker.
Writing images to disk
Built images go in output-angstrom-.9/deploy/eglibc/images/. Full, bootable ROM images are named rom-chumby-MACHINE-IMAGENAME.img. Other interesting files, such as the bootloader, boot shell, kernel, and boot graphics are also present in this directory.
To write a ROM file to disk, use dd, or on Windows use win32-image-writer. If you're working on a remote system, use SCP or SFTP to download the image file locally. Then write the file out to an SD card:
- Determine what drive letter your SD card is. After inserting the card, run "dmesg" and note the drive name. For example, it might be "sdb" or "sdc" depending on how many hard drives your system has.
- Unmount the drives
- for i in $(ls -1 /dev/sdb*); do sudo umount $i; done
- Write the ROM image out
- sudo dd if=rom-chumby-silvermoon-chumby-starter-image.img of=/dev/sdX bs=8M
- Download win32-image-writer from https://launchpad.net/win32-image-writer
An example of a ROM image may be downloaded from . Un-gzip this file and write it to an SD card, then insert the card in a Falconwing-based device. It should boot, and eventually bring up a prompt on the serial console.